Game Pro 200 CLONE

HotDog-Cart · Post by **HotDog-Cart** » Thu Aug 18, 2005 4:55 pm

Hey i was seraching around my house, and i found a thing thats about the size of a Non-Foldable cell phone, my guess is that its a Game Pro 200 clone since it has a B&W LCD screen, and it plays some of the games a game pro plays

its called a GSM 1997 in 1(it also has the word MR668 on it), will G-Force's Tutorial on how make a Game Pro 200 in a Altoids case work with this clone? I know its a lot smaller than a Game Pro.....

and My speaker is broke on it..The wires or disconnected form the speaker, anyway i can fix that?

it has 8 buttons (up, down/Mode, Left/Level, Right/speed, rotate/Shooting, Pause/start, Sound, and On/Off)

it takes 2 AA Batteries, too bad my screen is all scratched..anyway i can Buffer those out??
it looks like it takes some weird screw, ill try and get it apart with my Mini Screw Kit

HotDog-Cart · Post by **HotDog-Cart** » Thu Aug 18, 2005 5:40 pm

Bump, fromage HAHAH Cheese

Post by **Triton** » Thu Aug 18, 2005 5:51 pm

dude you bumped it because they didnt anwser in an hour?...

G-force · Post by **G-force** » Thu Aug 18, 2005 6:07 pm

It should work fine. Just use whatever is similar in the how-to and adapt it for your clone.

It prolly uses a tri wing screw, instead of normal phillip or flathead.

HotDog-Cart · Post by **HotDog-Cart** » Thu Aug 18, 2005 6:14 pm

i unno what screw it looks like a screw with no Bit hole, like a screw with no bit indent so nothing can take it out

HotDog-Cart · Post by **HotDog-Cart** » Thu Aug 18, 2005 6:32 pm

i dont think it has a Game 200 board...and why d i ahve to buy all taht extra stuff? i already have buttons..and it can alrready fit ina altoids can

sam · Post by **sam** » Thu Aug 18, 2005 10:44 pm

G-force wrote:It should work fine. Just use whatever is similar in the how-to and adapt it for your clone.

It prolly uses a tri wing screw, instead of normal phillip or flathead.

I need your help making one of those.

HotDog-Cart · Post by **HotDog-Cart** » Fri Aug 19, 2005 9:22 am

dammit.....One of the Wires that connect to the Battery pack, fell off, anyway i can make it work with out the battery, or is there anyway i can attach taht wire back on? (it needs to be soldered, but i dont have a Solder iron, so is there any way to make a subsitute Solder Iron?

Post by **bicostp** » Fri Aug 19, 2005 9:28 am

Just go to Radio Shack and buy a soldering iorn, there isn't any way to make a "substitute" iorn.

You'd probably need to re-attatch the battery wire. It wasn't put there for show, after all.

HotDog-Cart · Post by **HotDog-Cart** » Fri Aug 19, 2005 9:33 am

ok thanks...but i dont know if theres a RadioShack in Canada, liek ive saw one, but it was liek 2 comapnies in 1

and just by rubbing the wire agisnts the battery solder im gettin a small Reception

Jeff · Post by **Jeff** » Fri Aug 19, 2005 11:06 am

HotDog-Cart wrote:ok thanks...but i dont know if theres a RadioShack in Canada, liek ive saw one, but it was liek 2 comapnies in 1

and just by rubbing the wire agisnts the battery solder im gettin a small Reception

There was 2 months ago...its called The Source now.

Actually, in a few months it'll be called Radio Shack again, so right now its the Source. Confusing, eh?

HotDog-Cart · Post by **HotDog-Cart** » Fri Aug 19, 2005 4:26 pm

ya, ive been to the source very handy place, but kinda expensive, like $30 for Need For Speed Underground for Computer, like its usually $15