N64p guide!!!!!!!!

nos_slived · Post by **nos_slived** » Sun Jul 24, 2005 7:22 pm

Yes, my mistake. I had a miscalculation. I made a mistake on the diagram too. The resistors in parallel should be 10k, 3.9k, 3.9k, and 1.5k(yes, two 3.9k ohm resistors).

Godzilla · Post by **Godzilla** » Sun Jul 24, 2005 8:12 pm

What's the source of the whole "NUS-001s can take higher voltage" thing, anyway? Official tech specs? Trial and error? What? How reliable is it?

Post by **Gamelver** » Sun Jul 24, 2005 8:29 pm

um....I'm not very sure on that whole NUS-001 thing, actually

...but others say that on the NUS-001 N64s 5V can be inputted into the 3.3V line...has anyone tested this yet?

Godzilla · Post by **Godzilla** » Sun Jul 24, 2005 10:11 pm

Eh, I'll just do the 1.2 thing. So, just to confirm:

I'll need a 7805 and 6 one-ohm resistors.
I hook up 5 of the resistors in parallel to create a .2 ohm resistor.
I put the 7805 in series with my one-ohm and my .2-ohm resistors.
This will reduce incoming voltages down to a range of 3.2 to 3.56 volts for the amount of amps an N64 uses.

Have I understood this all correctly?

Post by **Gamelver** » Sun Jul 24, 2005 10:36 pm

yup

. just make sure that the resistors are rated for at least 5W of power...

loverare · Post by **loverare** » Fri Aug 05, 2005 5:22 am

I have a 7,2v 720mAh battery. It is enough for feed my screen and my N64, no?

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Fri Aug 05, 2005 7:16 am

no go for 2000 3000 ma

loverare · Post by **loverare** » Fri Aug 05, 2005 8:55 am

And if I take 6 AA 1.2V 1800mAh , it's good?

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Fri Aug 05, 2005 9:07 am

yeah 1800 ma, that should be ok but it wont give you a really good battery life

loverare · Post by **loverare** » Fri Aug 05, 2005 9:24 am

Ok thanks
I don't understand several details, but my diagram is correct, no?
If it is false, can you correct him?
[img]C:\Documents%20and%20Settings\Administrateur\Mes%20documents\Mes%20images[/img]

loverare · Post by **loverare** » Fri Aug 05, 2005 9:27 am

Ok thanks
I don't understand several details, but my diagram is correct, no?
If it is false, can you correct him?
[img]C:\Documents%20and%20Settings\Administrateur\Mes%20documents\Mes%20images\cablage.jpg[/img]

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Fri Aug 05, 2005 9:28 am

you gotta enter that at http://www.imageshack.us

go to forum 42 and it will show you how, you can probably just figure it out though

loverare · Post by **loverare** » Fri Aug 05, 2005 9:33 am

ok
http://img130.imageshack.us/img130/7621/cablage3hw.jpg

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Fri Aug 05, 2005 9:41 am

yeah that should work but if you can find a way to use one power source it may be better any way good luck

loverare · Post by **loverare** » Fri Aug 05, 2005 9:47 am

Sorry, but my English is limited. If I have correctly understand, my N64p will work but it's will be better if I have one source power and not two,
yeah?