Intec PS2 LCD,read last post about 3 way switch.

Dark Savant0 · Post by **Dark Savant0** » Thu May 12, 2005 12:46 pm

Would anyone care to help me? I know you guys dont like me, it obvious since no one answers my other topics, but I am really asking for help. Anyone?

I just want to know so I can wire the stuff straight to the board.

Dark Savant0 · Post by **Dark Savant0** » Sat May 14, 2005 10:41 am

Bump.

westbook2 · Post by **westbook2** » Sun May 15, 2005 10:02 pm

http://benheck.com/ipw-web/bulletin/bb/ ... 9&start=21

Dark Savant0 · Post by **Dark Savant0** » Mon May 16, 2005 4:12 pm

Umm, thats PSONE, not PS2.

Any help?

daguuy · Post by **daguuy** » Mon May 16, 2005 4:25 pm

disect a PS AV cable to see where Right, left, video and ground are on the plug if you can't find the pinouts on POD or something. if you found those, you will be able to tell what the pinouts for the A/V plug on the screen are. from there you can trace them to the board

Dark Savant0 · Post by **Dark Savant0** » Mon May 16, 2005 4:55 pm

How much power does the screen take?

daguuy · Post by **daguuy** » Mon May 16, 2005 5:19 pm

do you have one or know somebody who has one? that kind of stuff usually says it somewhere on the case

Dark Savant0 · Post by **Dark Savant0** » Mon May 16, 2005 5:31 pm

Says "DC IN 12V".

Any suggestions on connecting a battery?

nos_slived · Post by **nos_slived** » Mon May 16, 2005 5:45 pm

8 alkaline AAs. 10 Ni-Cad or Ni-MH AAs. Car battery?

daguuy · Post by **daguuy** » Mon May 16, 2005 5:57 pm

lead acid 12v battery (smaller than car battery

) it's got long life

ShaolinDrunkard · Post by **ShaolinDrunkard** » Mon May 16, 2005 6:39 pm

I posted it under "Intec ps2 screens". Its just down the list a little, take a look. And by the way the Intec ps2 screen will run of 9v.

ShaolinDrunkard · Post by **ShaolinDrunkard** » Mon May 16, 2005 6:52 pm

Darksavant0 are you still talking about the controller screen. Send me a private message with exactly waht you need to know.Sorry but i didnt get your last private message until today.

Dark Savant0 · Post by **Dark Savant0** » Tue May 17, 2005 5:02 am

It is the BIG one, not the control screen.

Do you guys think I can just solder 9v to the pin behind the plug? And desolder the plug and resolder it to a three way switch? Thanks.

Dark Savant0 · Post by **Dark Savant0** » Sat May 21, 2005 11:36 am

Umm, this is about the Regular Intec PS2 LCD, not the controller one. But that is not important really anyways.

Here is my question. I am making a 3 way switch, but dont know a part number for the DC input and a part number for dc ouput. I would prefer if they were from radioshack so I can get them easily. However, other part numbers are fine. I am looking for the part numbers to a DC Input, so that I can connect a regular plug in, and a dc output, so I can connect the positive and negative together again to form another plug. That way I dont have to canabilize the system. Any help?

I FINALLY REGISTERED. · Sat May 21, 2005 11:48 am

benheck.com Forums

Intec PS2 LCD,read last post about 3 way switch.

Intec PS2 LCD,read last post about 3 way switch.

HELP!