Check my COMPLETE diagram please.

Dr. KillGood · Post by **Dr. KillGood** » Sat May 31, 2008 2:23 am

Ok so I figured out what I am doing for the most part, thanks to triton and not-as-much Skyone. I have completed my diagram, and would like someone to check it for me!

So how does it look? I only show the back 3rd of the yobo but the other 2 parts are there lol!

Thanks.

Sharp Sapphire · Post by **Sharp Sapphire** » Sat May 31, 2008 7:22 pm

You created wireless electricity?

Post by **bicostp** » Sat May 31, 2008 7:25 pm

No, he invented Portals. See the circles in the diagram?

Looks like it should work just fine.

Post by **Skyone** » Sat May 31, 2008 7:39 pm

Dr. KillGood wrote:Ok so I figured out what I am doing for the most part, thanks to triton and not-as-much Skyone.

Not my fault that Triton is stubborner than I am, I just gave up on you.

Sharp Sapphire · Post by **Sharp Sapphire** » Sat May 31, 2008 7:44 pm

Ah, thanks for clearing the confusion bicostp. Ehehehe..

Dr. KillGood · Post by **Dr. KillGood** » Sun Jun 01, 2008 12:14 am

Sharp Sapphire wrote:Ah, thanks for clearing the confusion bicostp. Ehehehe..

I used my mini portal gun to make the wires shorter! =D

Dr. KillGood · Post by **Dr. KillGood** » Sun Jun 01, 2008 3:55 am

Ok so like, I got the LCD to run off the batteries, and the yobo is still on wall-plug.

My point is, when I turn them both on, I get no picture on the LCD!

LCD ON W00T!

In the right spots.

Connections look good right?

So why is it not working? I am trying to play super Mario 3.

Sharp Sapphire · Post by **Sharp Sapphire** » Sun Jun 01, 2008 5:43 am

Ground.

mothatrucka · Post by **mothatrucka** » Sun Jun 01, 2008 5:49 am

Gotta have that black ground wire connected.

WhatULive4 · Post by **WhatULive4** » Sun Jun 01, 2008 10:11 am

Sharp Sapphire wrote:Ground.

You think he would have noticed that :/

Dr. KillGood · Post by **Dr. KillGood** » Sun Jun 01, 2008 1:57 pm

I did do the ground, is it supported to go on the YOBO nes board? I soldered it to the same spot as the LCD ground?

Aguiluz · Post by **Aguiluz** » Sun Jun 01, 2008 4:15 pm

Dr. KillGood wrote:I did do the ground, is it supported to go on the YOBO nes board? I soldered it to the same spot as the LCD ground?

If you look closely, a black wire was not attached.

Post by **gannon** » Sun Jun 01, 2008 5:04 pm

Yes, at the moment there should be 3 wires between the yobo and lcd (audio, video, and ground), so you need to connect the ground wire to the yobo

Dr. KillGood · Post by **Dr. KillGood** » Sun Jun 01, 2008 5:14 pm

Well where does the black wire attach to the YOBO?

schmellyfart · Post by **schmellyfart** » Sun Jun 01, 2008 5:25 pm

Any of the sides of where the a/v jacks used to be. Its the big long contact that nearly every component is connected to.

benheck.com Forums

Check my COMPLETE diagram please.

Check my COMPLETE diagram please.

Re: Check my COMPLETE diagram please.