It's a me, BÃg Ã

BÃ¬g ANdÃ · Post by **BÃ¬g ANdÃ** » Mon Jul 24, 2006 1:07 pm

Hello all, i'm back. Not much has happened in the past, what, 3 months or so, so I never posted since april (sigh

) but i was just going to write up on my previous experiences in my life - past 1 month - when my account was deleted! from the database. So, here i am, the reformed BÃg Ã

ShockSlayer · Post by **ShockSlayer** » Tue Jul 25, 2006 9:06 am

[quote="BÃ¬g ANdÃ

BÃ¬g ANdÃ · Post by **BÃ¬g ANdÃ** » Tue Jul 25, 2006 12:33 pm

ok

do you want to know about my cartridge slot????????????????????????

ShockSlayer · Post by **ShockSlayer** » Tue Jul 25, 2006 1:04 pm

[quote="BÃ¬g ANdÃ

BÃ¬g ANdÃ · Post by **BÃ¬g ANdÃ** » Wed Jul 26, 2006 3:30 am

its not all that big really, but i can't fix it.

what happened was that i went to my friends house (cause he's helping me) and we were going to work on the n64

. to do the cartridge slot, we were going to use the method where you get an old priter cable, take all the 50 cables inside out of the rubber casing, and basically solder them to the pins on the cart slot and the corresponding ends on the motherboard. Easy.

It wasn't really. We both had soldering irons, but we arn't all that good at soldering!!! So we tried to solder onto the first pin. It didn't stick on, tried again. nothing! i asked my friend if he could get some lemon juice for me, and while he was away, i picked the cart slot, and the pin fell off

!!!!!!!!!

we tried on three other pins, with lemon juice, and two of them fell off

. So that's my escapade from last week. Any Questions

Post by **CronoTriggerfan** » Wed Jul 26, 2006 8:03 am

If you're THAT bad at soldering ( I SUCK at it but I can still relocate a cart slot) then practice. Get spare motherboards and desolder/solder components to it. That, or just don't relocate the cartridge slot. It was never a big deal to me, but some people have it as a pet-peeve.

CTFan

BÃg Ã · Post by **BÃg Ã** » Wed Jul 26, 2006 11:30 am

yeah, good idea. Oh and by the way, i re-activated my account as BÃg Ã

BÃg Ã · Post by **BÃg Ã** » Fri Jul 28, 2006 2:07 am

i found this battery on ebay, by the way, which i'm about to buy. is it powerful enough to run an n64 with a ps1 sceen hooked up to it.

here's the link http://cgi.ebay.co.uk/8-4v-NiMH-3300mAh ... otohosting

BÃg Ã · Post by **BÃg Ã** » Fri Jul 28, 2006 10:44 am

i should be able to fit two into my design fine, and i thought about buying the 8.4v battery, because thats what i read on some other site that you nedded to run the screen

demonofaj · Post by **demonofaj** » Fri Jul 28, 2006 12:14 pm

Ah, the pin fell off, on my X portable's cart slot, that sadly happened, and I couldn't acquire another slot, so, I noticed that a bit of the metal was exposed, so I melted the plastic around it, just a LITTLE bit, so I could expose a bit more method, so then it's good

BÃg Ã · Post by **BÃg Ã** » Fri Jul 28, 2006 12:29 pm

ahhh, nice one. i'll try it myself

BÃg Ã · Post by **BÃg Ã** » Wed Aug 02, 2006 4:38 am

It didn't work for me unfortunatly

, so i just bought a new N64 instead.
It only cost me Â£6.99 ($10-$14), so i'm good.

And I just set up my own site.

BÃg Ã · Post by **BÃg Ã** » Thu Aug 03, 2006 4:59 am

BTW, what voltage of hotglue do I need. I found http://cgi.ebay.co.uk/New-Nutool-12w-El ... dZViewItem this one. It's only 12v, so i'm not sure if its that powerful.

BÃg Ã · Post by **BÃg Ã** » Fri Aug 04, 2006 4:12 am

never mind about the hot glue gun, but I got my N64 this morning, and it works perfectly

. The only bad thing is I don't know what age it is

benheck.com Forums

It's a me, BÃg Ã

It's a me, BÃg Ã

Re: It's a me, BÃg Ã

It's a me, BÃ­g Ã

It's a me, BÃ­g Ã

Re: It's a me, BÃ­g Ã

It's a me, BÃg Ã

It's a me, BÃg Ã

Re: It's a me, BÃg Ã