SNESp -- Let me buy one off you.

Klefmung · Post by **Klefmung** » Sat Jul 22, 2006 5:00 pm

I'm coming, triiiitoooon!

Post by **Triton** » Sat Jul 22, 2006 5:50 pm

dont knw if i should be glad or grossed out

heres a little teaser, going to be redoing the paint and more bondo too buit this is basically it

Klefmung · Post by **Klefmung** » Sat Jul 22, 2006 5:53 pm

Is the screen LED modded or no? Are you using RGB video? Are you gonna put buttons over those tact switches?

blackbox_dev · Post by **blackbox_dev** » Sat Jul 22, 2006 6:24 pm

He told me that the screen isn't LED modded and in one of the other pics he showed me there were buttons over the tact switches, so I'd say yes to that...

Post by **Triton** » Sat Jul 22, 2006 6:27 pm

actually no to all 3 lol, the tact switches are asier to use without buttons and i always had problems witht he dpad over tact switches for some reason, i tested it and it draws a hefty 1.3-1.5 amps >.< i think ill lower the brightness on the lcd a bit casue its maxed out, that should save a bit anyway

Post by **Skyone** » Sun Jul 23, 2006 1:12 am

This is gonna be a very "throw it out there" portable, isn't it?

vb_master · Post by **vb_master** » Sun Jul 23, 2006 6:12 am

Klefmung wrote:I'm coming, triiiitoooon!

............................................________
....................................,.-â€˜â€

Klefmung · Post by **Klefmung** » Sun Jul 23, 2006 11:31 am

Triton wrote:actually no to all 3 lol, the tact switches are asier to use without buttons and i always had problems witht he dpad over tact switches for some reason, i tested it and it draws a hefty 1.3-1.5 amps >.< i think ill lower the brightness on the lcd a bit casue its maxed out, that should save a bit anyway

At least use RGB video. <_<

Post by **Triton** » Sun Jul 23, 2006 2:02 pm

throw it out there? now that i dont have a deadline of going from less than 50% to done in 2.5 days i will be able to improve it a bit, and how do i do rgb? is it that much better?

Klefmung · Post by **Klefmung** » Sun Jul 23, 2006 2:05 pm

Since that is a V1 mobo, you can use RGB (you can on a mini, but you have to get it off the chroma encoder instead). RGB=Sex. Use this Pinout as to where to put the red, green, and blue on the screen, and this pinout for where to get the red, green and blue from the SNES.

Post by **Triton** » Sun Jul 23, 2006 6:32 pm

so the video is that much better eh?

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Sun Jul 23, 2006 6:51 pm

snesguy says its fantastic, i wish i couldve done it on my snesp mk2 but there is no known way on a hipgear yet

grahf · Post by **grahf** » Fri Aug 04, 2006 11:14 pm

I tried doing RGB on a hipgear, with no success. I have the datasheet for the IC, and it DOES have RGB input. You also have to provide a proper sync, and change a pin from low to high to activate RGB. I may have missed something, but i read over the datasheet for a few hours total. The pins are just so incredibly hard to solder to, that i gave it up. I even did all my soldering under a scope, but its still damn hard.

pwherman · Post by **pwherman** » Sat Aug 05, 2006 10:22 pm

Can anyone maybe help Triton out here? There's some unknown problem with the Mobo. It was thought to be the CIC Lockout Crystal, but on replacement, the problem persisted.

He's been working on this ever since early May and I'd really like for him to be able to finish and complete this sale to me, but he's stumped.

ShockSlayer · Post by **ShockSlayer** » Mon Aug 07, 2006 6:52 pm

Open up a completely new snes, working, and take a pic of the mobo. Take a pic and then compare.

SS