GCp rebuilding thread

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Wed Mar 01, 2006 8:20 pm

im thinkin about buyin some of these li-polys for the rebuilding
http://batteryspace.com/index.asp?PageA ... rodID=2171
they are only 2500 mah but i dont think i will be playing it for that long away from some kinda power supply and i may buy some more and wire them in parrelel when i get more money and if it turns out well

Zzebotes13 · Post by **Zzebotes13** » Wed Mar 01, 2006 8:41 pm

how do you connect li-plies to the system and be able to charge them, obviuosly i've never used them. Just thinking about using them because they would be smaller than the huge 12v 3300mah batt. i was thinking of getting.

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Wed Mar 01, 2006 9:19 pm

what do you mean because you can do that with any rechargeable battery check out PoD

Post by **Skyone** » Wed Mar 01, 2006 9:46 pm

Pretty thin, I like it. The only problem is that if you like to play tons like I do, you should get a higher mAh than that. I figure that will only get you 2-3 hours TOPS. Depending on if you do an LED screen mod or not. 2-3 hours is actually not that bad considering how hard it is to find good batteries.

elementxmaster · Post by **elementxmaster** » Thu Mar 02, 2006 11:40 am

Zzebotes13 · Post by **Zzebotes13** » Thu Mar 02, 2006 12:01 pm

what i mean is, can you have the batts charging from the intergrated charger, and use the system at the same time, or will it kill the batteries.

elementxmaster · Post by **elementxmaster** » Thu Mar 02, 2006 12:25 pm

Zzebotes13 · Post by **Zzebotes13** » Thu Mar 02, 2006 1:43 pm

so i can charge thcube at the same timee batteries and use the time

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Thu Mar 02, 2006 1:50 pm

not unless you have a special circuit or your battery was meant to do that and i think th3e GC battery was meant to do that
o and as far as the case goes my table is trashed so im tryin to get gamelver to make one whenever he makes a case for one of his potables. but if i have time spare time and money i may try and build a new nicer table that can handle big molds

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Thu Mar 02, 2006 4:40 pm

14.8 volts how easy do you guys think it would be to separate each cell in this pack i rewally want to get some li-polys of this ma but they dont have 4 in stock but they have this

extremesonic · Post by **extremesonic** » Thu Mar 02, 2006 4:53 pm

What does the cube need to run(voltage and mah)? I know it has the DC-DC in the power supply that converts 12Vish to 3-4 different voltages, but what is the highest outputted voltage form the DC-DC that the cube actually uses to run?

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Thu Mar 02, 2006 4:54 pm

12 volts i think because there are pins that output 12volts on the board

Zzebotes13 · Post by **Zzebotes13** » Thu Mar 02, 2006 6:27 pm

here are the batteries
http://batteryspace.com/index.asp?PageA ... D=217[url]
after connecting the batteries in series, could i then just attach a male r/c car battery adapter to it to charge them. I'd be using a smart charger from batteryspace. Thjis way, i could switch from charger te batteries and using them to power the system

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Thu Mar 02, 2006 8:19 pm

if you have the batteries wired to a protection circuit then sure you can charge and play at the same time

elementxmaster · Post by **elementxmaster** » Fri Mar 03, 2006 10:10 am