PSone screen voltage

geekbait111 · Post by **geekbait111** » Sun Feb 19, 2006 6:44 pm

Hihi, anyone know hom many volts a 5" PSone intec screen takes up?

Kurt_ · Post by **Kurt_** » Sun Feb 19, 2006 6:46 pm

geekbait111 · Post by **geekbait111** » Sun Feb 19, 2006 7:44 pm

Skyone wrote this:

Pretend the area that says 7805 is the gray/black area on the 7805 regulator.

All you have to do is throw anywhere from 7.2 volts to 32 volts onto the input voltage, and the negative/ground of the battery onto the ground of the 7805.

That's it!

EDIT: Hey! That's my thread you found! Smile

So I need min 14.6 volts to power the sega v.3. That would make 12 Nimh batteries???? Then how did G-Force http://www.customizin.tk/ make the Ondago with 6 rechargable batteries??? Can someone tell me how to reduce that amount???

akadewboy · Post by **akadewboy** » Mon Feb 20, 2006 2:40 am

You only need 7.2 volts in batteries. Run 1 wire from the batteries to the 7805 (this will knock the voltage down to 5 volts). Run the output of the 7805 to the Genesis.

Now run a second wire from the batteries (7.2 volts) straight to the PSone screen. You don't need seperate batteries, you can run both the screen and the Genesis on the same batteries.

geekbait111 · Post by **geekbait111** » Mon Feb 20, 2006 8:31 am

akadewboy boy said:

You only need 7.4 volts in batteries. Run 1 wire from the batteries to the 7805 (this will knock the voltage down to 5 volts). Run the output of the 7805 to the Genesis.
Now run a second wire from the batteries (7.4 volts) straight to the PSone screen. You don't need seperate batteries, you can run both the screen and the Genesis on the same batteries.

Would I run the battery first to the input or ground on the 7805?
edit: never mind about the input, but look below for the ques. about the ground.
edit: sorry akadewboy

geekbait111 · Post by **geekbait111** » Tue Feb 21, 2006 1:14 pm

As seen above, I was wondering about the battery, but where do you find the ground of the case-thing for the 9 volt (which wire)?
http://www.stewmac.com/shop/Electronics ... ml#details
. Because I was wondering what wire you solder to the ground of the 7085 (I
know the other stuff about the 7805)

Trv · Post by **Trv** » Tue Feb 21, 2006 8:50 pm

geekbait111 wrote:Awkward boy said:

yeah.. that's not his name

Anyway. The ground is just the negative terminal of a battery. So run a wire (the black one) from the negative terminal to the ground on the 5v reg

geekbait111 · Post by **geekbait111** » Wed Feb 22, 2006 4:24 pm

So that means I would wire the red to the PSone screen and nothing to the input?

Trv · Post by **Trv** » Wed Feb 22, 2006 4:36 pm

geekbait111 wrote:So that means I would wire the red to the PSone screen and nothing to the input?

Please clearify this.

But as far as i can tell. the red wire (positive) goes into the psone AND the input of the 5v regulator. The black wire goes into the ground on both the psone screen and the regulator. the output of the regulator goes into the snes

geekbait111 · Post by **geekbait111** » Wed Feb 22, 2006 5:28 pm

how does it go into both

Trv · Post by **Trv** » Wed Feb 22, 2006 5:57 pm

geekbait111 wrote: how does it go into both

Well... You buy some wire from radio shack. Cut two peices. Solder both of them to the end of positive wire..... Thus making two wires to connect......... dot dot dot

geekbait111 · Post by **geekbait111** » Wed Feb 22, 2006 7:08 pm

Oh............... Thanks a bunch!