Intec Screen Pad Question.

jeffslot · Post by **jeffslot** » Tue Nov 08, 2005 4:26 pm

Hello,

Can someone please help me out & help get my project re-started. I need to know what the circled in red pins are for. Thanks.

Jeff S.

http://img471.imageshack.us/img471/6034 ... xj.opt.jpg

daguuy · Post by **daguuy** » Tue Nov 08, 2005 5:42 pm

AV and power and all that stuff. BTW, how long is the ribbon cable for the LCD?

jeffslot · Post by **jeffslot** » Tue Nov 08, 2005 5:55 pm

daguuy,

That is the thing that is really confusing me. My screen pad only seems to have 1 row to connect to? Help.

Jeff S.

demonofaj · Post by **demonofaj** » Tue Nov 08, 2005 5:59 pm

I'm not sure, but I think you have the INTEC one?

jeffslot · Post by **jeffslot** » Tue Nov 08, 2005 7:32 pm

Any one have any useful info about the intec screen pad pin-out?

daguy, I though your info was usefull.

Thanks

Jeff S

G-force · Post by **G-force** » Wed Nov 09, 2005 8:08 am

Sorry, I don't have one. If you had checked the wires before you desoldered them you could have figured it out. Do you still know how they were soldered on? If so you coudl just trace each wire to what ever it is on the adjust board.

jeffslot · Post by **jeffslot** » Wed Nov 09, 2005 8:23 am

G-force wrote

Sorry, I don't have one. If you had checked the wires before you desoldered them you could have figured it out. Do you still know how they were soldered on? If so you coudl just trace each wire to what ever it is on the adjust board.

You're right, not only am I feeling stupid, I'm feeling embarressed. Can anyone help? I'm hoping that someone has a similar screen pad. Thanks.

daguuy · Post by **daguuy** » Wed Nov 09, 2005 4:02 pm

maybe if nobody has the pinouts, you could test each pin with a video signal

Foxx373 · Post by **Foxx373** » Wed Nov 09, 2005 11:36 pm

I have the same problem. My 2.5" intec screen control pannel was crushed completely. Anyone know how to input into it, or can rebuild a replacement, let me know.

gamemasterAS · Post by **gamemasterAS** » Sat Nov 26, 2005 9:27 pm

i have an intec gamecube screen im using for my portable snes.The problem is i heard something about it neading 20v.

Harshboy · Post by **Harshboy** » Sat Nov 26, 2005 9:53 pm

woah! thats a lot of voltage! but the screen only needs 12 volts( the intec gamecube one ) I have it and since it leeches of the gamecube power cable it must use 12 volts or less........helpful or not?

madc0w · Post by **madc0w** » Sat Nov 26, 2005 10:03 pm

it probably uses a 7508 or a 7505, so it would take 9 and 6 volts respectivly.

nos_slived · Post by **nos_slived** » Sun Nov 27, 2005 1:47 am

EDIT:

gamemasterAS · Post by **gamemasterAS** » Sun Nov 27, 2005 1:20 pm

so i nead to get 12 volts of power just to make the screen work

daguuy · Post by **daguuy** » Sun Nov 27, 2005 1:25 pm

if it's the older model (not huge pcb) it should work down to around 5v

benheck.com Forums

Intec Screen Pad Question.

Intec Screen Pad Question.

help!!!!!!!