Damn PSONE Screen GND1 point.

demonofaj · Post by **demonofaj** » Fri Mar 10, 2006 8:45 pm

This point is freaking impossible to solder to! It's the one sligtly above the main bottom components on the back board? Any tips on soldering to this ground, and uh...will soldering to the ground on the 7805 to the right of the board, serve as an appropiate ground for power and video/audio?

demonofaj · Post by **demonofaj** » Sat Mar 11, 2006 8:54 am

Boomp!

atkafighter · Post by **atkafighter** » Sat Mar 11, 2006 9:30 am

Use the square on the front left of the screen. The small GND pad usually comes off.
Hope this helps
Atkafighter

demonofaj · Post by **demonofaj** » Sat Mar 11, 2006 9:36 am

Thanks

, and by that, do you mean the screwhole? Also, would it stick or just slip off.

Weebl · Post by **Weebl** » Sat Mar 11, 2006 4:00 pm

No there's a silver rectangle that's ground that's to the left of the screen and not the screw holes. If you were to look at the two screwholes to the left, its about halfway between the two.

Harshboy · Post by **Harshboy** » Sat Mar 11, 2006 4:11 pm

strip the second wire on the first port and connect ground to it. Like this:

Now you can also cut the first wire and strip it and connect the Possitive to that......and then just twist. Then wrap electric tape around em and you're good to go

Klefmung · Post by **Klefmung** » Sat Mar 11, 2006 4:12 pm

a lot of the wires coming from the ports are ground. Look at the diagram in the FAQ for further elaboration.

Harshboy · Post by **Harshboy** » Sat Mar 11, 2006 4:16 pm

Yes, but those two wires are the ones ment for the power

Why? They go to the power pcb

Klefmung · Post by **Klefmung** » Sat Mar 11, 2006 4:18 pm

I don't believe 4 and 8 in the right front slot do.

Harshboy · Post by **Harshboy** » Sat Mar 11, 2006 4:23 pm

what are you talking about?

Klefmung · Post by **Klefmung** » Sat Mar 11, 2006 4:25 pm

fourth wire in the right slot if it was facing the front anf the 8th wire in the same context. >_>

superdeformed · Post by **superdeformed** » Sat Mar 11, 2006 5:59 pm

The other grounds on the connector are meant for the video and audio signals, and should not be used for the main power ground. They may all be connected to the same spot, but you still want to keep things like that seperated to avoid noise. It may not make a difference in this case, but it's still a good practice.

Harshboy · Post by **Harshboy** » Sat Mar 11, 2006 6:11 pm

Klefmung wrote:fourth wire in the right slot if it was facing the front anf the 8th wire in the same context. >_>

I still have no idea what you're talking about....is it my picture?

Klefmung · Post by **Klefmung** » Sat Mar 11, 2006 8:21 pm

If you don't understand english, then here we go!
Vierter Draht im richtigen Steckplatz, wenn es dem vorderen anf der 8. Draht im gleichen Kontext gegenÃ¼berstand!
I put it as simple as possible.

Harshboy · Post by **Harshboy** » Sat Mar 11, 2006 10:40 pm

Klefmung wrote:If you don't understand english, then here we go!
Vierter Draht im richtigen Steckplatz, wenn es dem vorderen anf der 8. Draht im gleichen Kontext gegenÃ¼berstand!
I put it as simple as possible.

Sorry, don't understand Spanish either.