Stuff for sale... (Updated 08.11)

mothatrucka · Post by **mothatrucka** » Tue Jun 17, 2008 6:36 pm

Gone on e-Bay.

I still do custom-cut plexi/perspex/acrylic sheeting. I have clear, in 1/8" (3mm) and 1/4" (6mm) thicknesses. PM me for prices.

mothatrucka · Post by **mothatrucka** » Wed Jun 18, 2008 9:59 pm

Bump. Added a few more things to the trade list.

bacteria · Post by **bacteria** » Wed Jun 18, 2008 10:57 pm

I have spare NES controllers; always need more plexiglass (perspex), what size and thickness do you have? What country are you in? (perspex is heavy).

weaponepsilon · Post by **weaponepsilon** » Thu Jun 19, 2008 2:04 am

I have a whole guitar hero guitar that I planned to fix. I might be persuaded to let it go. I need some motors, like the ones in the rumble/dual shock controllers.

bacteria · Post by **bacteria** » Thu Jun 19, 2008 2:36 am

weaponepsilon - I have a couple of rumble motors from N64 controllers lying about if you need them. PM me if you want to discuss.

LoyalistRevolt · Post by **LoyalistRevolt** » Thu Jun 19, 2008 6:42 am

DUDE I NEED THAT PLEXIGLASS!!!

mothatrucka · Post by **mothatrucka** » Thu Jun 19, 2008 6:44 am

I literally have acres of the stuff laying around. I'll be back at the shop this afternoon, so I'll do up a list of what plexi I have.

weaponepsilon- What kinda voltage are you looking for on those motors? I've got some ripped from old electronics, but they're similar in physical size. I'll get some specs on those for you, too.

LoyalistRevolt · Post by **LoyalistRevolt** » Thu Jun 19, 2008 6:53 am

mothatrucka wrote:I literally have acres of the stuff laying around. I'll be back at the shop this afternoon, so I'll do up a list of what plexi I have.

weaponepsilon- What kinda voltage are you looking for on those motors? I've got some ripped from old electronics, but they're similar in physical size. I'll get some specs on those for you, too.

THANK YOU.

weaponepsilon · Post by **weaponepsilon** » Thu Jun 19, 2008 11:51 am

Well, the motors are going to be used for an entirely different project. Basically I'm going to run it with a 9 volt. Not sure on the specifics, just a passing thought that I had.

weaponepsilon · Post by **weaponepsilon** » Thu Jun 19, 2008 11:53 am

Well, the motors are going to be used for an entirely different project. Basically I'm going to run it with a 9 volt. Not sure on the specifics, just a passing thought that I had.

mothatrucka · Post by **mothatrucka** » Thu Jun 19, 2008 6:16 pm

All sizes in inches. Fractional inches have been rounded down. Most have protective wrap intact, but not all. All are clear unless stated otherwise. The prices listed are based on half of the current retail price for it in my area. I'm open to selling or trading on this but it's easier with a set value. Iâ€™ll have to look into shipping prices. Iâ€™m not sure what the best way would be.

If you need a custom size let me know and we can discuss pricing, shipping, etc. I can also do screwholes etc. I may even be able to talk a friend into doing holes for controllers and screens but there would be a small labor fee for that.

1/8â€

LoyalistRevolt · Post by **LoyalistRevolt** » Thu Jun 19, 2008 9:22 pm

If I gave you measurements could you cut to a specific size?

mothatrucka · Post by **mothatrucka** » Thu Jun 19, 2008 10:37 pm

Yeah. Is it just a regular rectangle you need? Let me know.

LoyalistRevolt · Post by **LoyalistRevolt** » Fri Jun 20, 2008 10:55 am

I'm building an arcade control panel and I need plexi for the top. When I get to my friends house I'll give you the specs. also would it be possible for you to put holes in it?

mothatrucka · Post by **mothatrucka** » Fri Jun 20, 2008 3:35 pm

LoyalistRevolt wrote:I'm building an arcade control panel and I need plexi for the top. When I get to my friends house I'll give you the specs. also would it be possible for you to put holes in it?

Depends on the holes. If you want me to do some screwholes, no problem. If you need a lot of holes for ventilation, or some cutouts for controls and other components, I'd want a bit for labor. Let me know what you need, and I'm sure we can work something reasonable out.